Technical Resource Hub


gobright iadea biamp lenovo ptzoptics Rocware maxhub logo rethink jupiter utelogy audiebant ProDVX Nureva
Sort:

Found 9 results

Installation 7 months ago

Factory Reset An Interact

Here's a simple guide to factory resetting your GoBright Interact.With a small screwdriver or a paperclip you can press the reset button for 5-10 seconds.Let the device fully reboot. You'll then need the GoBright app to scan the QR code shown on screen and link the Interact to the relevant desk / room.The GoBright app is available for free on both Apple and Android devices. Just check out your relevant app store and search for 'GoBright'.
22 hits
Lee Russell (@lee) February 10, 2026
Read More
Installation 3 months ago

ProDVX Firmware Re-Flash

If the device powers up as expected, but is stuck on the Android boot screen, please follow these steps to re-flash (factory reset) the ProDVX panel. You will need to re-install the relevant booking app after performing the following steps.Unplug everything from the device, including the power source.Press and hold the "Volume +" button.Whilst holding this button, provide power to the device (can be both PoE or PSU).Keep holding the button until the Android Recovery menu appears. In this menu, navigate using the volume (+/-) buttons to the format/wipe system option.Select this option by long pressing the circular menu button next to it.After confirming the reset, reboot the device and check and confirm whether it does so without any issues.After step 7, please be patient as it can take up to 10 minutes for the panel to reload. When the process is complete, you'll have a blank Android panel. As this process completely resets the panel, you'll need to reconfigure the network - so if you're using Wi-Fi you will need to re-authenticate.If you have any further questions, please contact support@ascentae.com to log a support ticket. It helps to speed things up if you provide:ModelSerial NumberProof of Purchase
9 hits
Lee Russell (@lee) June 22, 2026
Read More
Installation 7 months ago

Nureva HDL410 – Best Practice for Camera Integration Direct Integration

Nureva HDL410 – Best Practice for Camera IntegrationDirect Integration Before installing a camera steering and switching solution to integrate with your Nureva audio solution, we recommend you refer to the below information and important links.You can find comprehensive instructions on installing and configuring a Nureva / camera solution on the Nureva Support site.This article gives guidance you may not find online, plus some Top Tips that we have picked up.Understand the customer requirementsNureva can support both camera steering (tracking/switching presets), and camera switching (changing to different cameras).It is important to have a view of the customers room, and understand which areas of the room need to be covered by a camera.  From this, you can determine the number of cameras required and the fields of view.If you have any queries about this, please contact Ascentae for advice.  We can even offer a full pre-installation consultancy service to help with this.Understand the limitations of the technology – HDL300 / HDL310         When integrating with a HDL300 or HDL310, you have a single sound bar – and so only one point of reference.  The information passed to the camera controller is based on the central point of the sound bar.  This makes it an ideal solution for azimuth presets, with a single camera mounted in line with the centre of the sound bar.Typically, up to 8 presets can be configured, each covering 22.5° of the room.The same is true if you have the legacy Dual HDL300 system.  The reference point for camera tracking will be the centre point of the primary sound bar (plugged into port 1 on the Connect Module).  The 2nd sound bar is not used for camera tracking).If using more than one camera, the best position for the cameras is either side of the sound bar, each covering half the room and using 4 presets.Understand the limitations of the technology – HDL300 / HDL310The HDL410 has 2 sound bars and when correctly positioned in the room, they can deliver accurate X,Y coordinate information to the camera controller.  Depending on the sophistication of the camera controller, it can interpret those coordinates in different ways.                Select appropriate camera and steer to coordinate location                Select appropriate camera and steer using presets                Select appropriate camera and switch to pre-defined zoneNote:  Not all camera controllers support all these modes.  Refer the camera vendor documentation for details.Camera zoning is covered in detail in a separate knowledge base article.Choosing the correct cameraNureva have created a suite of API calls which different camera providers have utilized to integrate with the Nureva devices.  Currently these are Aver and Lumens, plus drivers and sound tracking modules by Crestron and Extron.Typically, each camera vendor has created a software camera controller (in some instances it may be a hardware device).  Nureva confirm compatibility with the camera controller.  However, not all cameras from a specific vendor will be supported on the controller software.  It is the responsibility of the integrator to confirm compatibility of cameras and camera control solution.Make sure you check the focus length / zoom capabilities of the proposed camera.  If you are installing in a large room, the camera should be able to zoom and focus clearly on the furthest participant.Currently supported camera drivers are as follows.Note that camera switching is not supported by PTZApp 2 (single camera only)Note that camera switching is not supported by CamConnect Lite (single camera only)Cameras that support preset recall and have a Crestron module can support sound location data.Cameras that support preset recall and have an Extron driver can support sound location data.Positioning of the Nureva Sound BarsFor the HL300 / HDL310 remember that the camera reference point is the centre of the sound bar.The ideal position for the sound bar is above the screen – allowing sufficient clearance for the audio to be reflected off the wall into the microphones.It is important that there is no obstruction underneath the sound bar as this will degrade audio quality and cause inaccurate sound location data.To ensure best audio performance, measure how far your screen sits from the wall, and mount the sound bar so the bottom is 1.5 x this distance.E.g.  if you screen sits 10cm proud of the wall, the bottom of the sound bar should be 15cm from the top of the screen.Refer to the Microphone clearance requirements guide for more detailshttps://support.nureva.com/docs/installation-hdl300-microphone-clearance-requirements-and-recommendations-2We recommend that cameras are mounted underneath the screen where possible, but if underneath HDL sound bar, allow at least 6” (15cm) clearance from the top of the camera to the bottom of the sound bar.Available ResourcesSupported camera solution - https://support.nureva.com/docs/supported-integrations-for-camera-switching-and-tracking-1Aver Integration Instructions - https://support.nureva.com/docs/integrate-aver-cameras-with-camera-trackingLumens Integration Instructions - https://support.nureva.com/docs/how-to-integrate-with-lumens-ptz-camerasCrestron Module Instructions - https://support.nureva.com/docs/use-crestron-sound-tracking-moduleExtron Driver Instructions - https://support.nureva.com/docs/using-extron-sound-tracking-driverWatch out for reflectionsCameras are dumb and can easily be confused by reflections in windows.Be mindful of setting presets that can catch reflected images, or setting the camera to track in areas where windows will reflect if it’s dark outside.Ideally, curtains or blinds will not only avoid this issue, but have the additional benefit of reducing echo and reverberation in the room and so improve performance of the HDL device.If in doubt, ask AscentaeWe are here to help.  Please ask if you need any guidance, or would like to engage us to do a consultation on HDL and camera integration.
8 hits
Nick Palmer (@nick) February 8, 2026
Read More
Installation 3 weeks ago

GoBright Advanced Gateway (AGW) Setup

The previous gateway models are the MGW211-DP24 and MGW211-DP28. This article is based on testing the AGW332-EU868 with firmware 1.0.0. We conducted these tests in August / September 2026.The GoBright Advanced Gateway is basically a solid piece of kit that hooks your devices upto the cloud. It makes sure all the data syncs perfectly and keeps your smart workplace online without any hiccups.Planning Your InstallationWhen figuring out where to put your gateway, keep an eye out for things that can block the signal—like thick concrete walls, metal objects, elevators, and stairs. If you hit any dead zones, just add a few extra Advanced Gateways to make sure the whole building gets solid coverage. Please see the planning and deployment guide here.The image to the left shows how the gateway looks once setup.The Small AntennaThis is used for Wi-Fi communication and both 2.4 GHz and 5GHz are now supported.The Large AntennaThis is used for any communication if LoRa sensors are being deployed.We've provided a step-by-step guide below to get you up and running. ⚠️You must be a administrator on the GoBright portal to ensure you can complete the following steps. The GoBright mobile app is required (Android or iOS) and it needs to be running the latest version.Power OptionsThe first step is to make sure that the toggle switch on the top of the gateway is toggled off of 'boot'.The gateway supports PoE+ at 30W. This is done through the ETH0 port. A 230v power supply is not included as standard and must be purchased seperately. Please speak to your Ascentae account manager when orderingOnce you've sorted power to the device, allow around 10 minutes for it to fully boot. During the boot process the LEDs will flash different patterns. At this stage, grab a brew and allow the device to boot and wait for the LEDs to slowly start blinking blue. This is a good sign as we're now in discovery mode, and the device is ready to commission. So, let's get cracking...Important Note: Discovery mode only remains active for up to 10 minutes after boot. Please reboot again if needed.Just a heads up...Configure The PresetIn your GoBright portal, head to Settings > Devices > Profiles and add a new profile name. Change the 'type' to 'Advanced gateway'. Hit save.Stay in the GoBright portal, and head to Settings > Devices > Commissioning Presets and then 'Add'. Change the Type to 'Advanced Gateway'. Give it a name, select the profile you've just set up, and enable the relevant connection settings. Save this page. This will then appear in the list under Settings > Devices > Profiles:As you can see, for testing purposes, we've called this 'Lee - Advanced Gateway'. At this stage, we recommend giving the device a suitable name - especially if deploying multiple devices across multiple floors.Now head to Settings > Devices > Commissioning Presets to locate your preset you just configured:Select the commissioning preset and ensure the connection details are correct. Both 2.4GHz and 5GHz Wi-Fi networks are supported. Switch To The GoBright App⚠️Ensure that bluetooth is enabled on the device that you're using to commission the gatewayNow we need to switch to the GoBright app as the device has booted. Navigate to Settings → Admin Tools → GoBright Advanced Gateways (beta) → GoBright Advanced Gateways. Scan the QR code on the back of the gateway. Select the following option:On the next step, select the pre-configured commissioning profile that you setup. Give the gateway a name and complete all the required information. Once ready, press 'Commission Device'.Next, you will see the following screen:Select 'Done' and you can see the device under the 'GoBright Advanced Gateways' option on the app. Once commissioned, there should be 2 green solid lights on the gateway.On the web portal, head to Settings > Devices > Gateways to see your device. Here you can:See the firmware it's running and update it if requiredSerial numberConnection statusLocal IP addressSummaryNow you have an active Advanced Gateway configured and setup in your portal.The LED indicators should look like this once successfully activated and enabled in your GoBright portal.If you have any questions, please log a support ticket. We're happy to help.Last Updated: 22/09/2026
5 hits
Lee Russell (@lee) September 1, 2026
Read More
Installation 7 months ago

Reset an Interact

You must be an admin to perform this action as access to the settings is required. If you do not have access, please speak to your GoBright Administrator.The GoBright App must be installed on your phone and you must be logged in as an Administrator.To reset the GoBright Interact device, log in to the GoBright portal and head to Settings > Devices > Interacts.Delete the device (step 3 above).The device will then show as offline:Place your finger on the 'Offline' section and swipe down to bring up the following:Select recommission and then confirm you wish to recommissionThe Interact will rebootYou are then presented with a QR code that needs to be scanned.You now need the GoBright App. Load the App and click on the 3 horizontal lines in the top right to bring up the settings menuSelect Admin toolsSelect GoBright InteractsSelect 'Commission an Interact by QR code'Select your commissioning presetScan the QR code on your phone that is logged in with an admin accountComplete the next page and make sure the Interact is coupled to the correct room / desk / parking spaceSelect 'Commission Device'After approximately 30 seconds the device will reboot.If your device is stuck on 'Connecting MQTT over TLS' please ensure that the following firewall rules have been applied:Outbound 8883 - Traffic over MQTT over TLS to the GoBright platformThe full firewall configuration can be found here:https://support.gobright.com/hc/en-us/articles/360010024559-Firewall-configuration
4 hits
Lee Russell (@lee) February 8, 2026
Read More
Updates 6 months ago

GoBright Interact Udpates

Below you will find a table containing all the information regarding the GoBright Interact firmware updates.Date Firmware Notes26/03/20262.5.32Various improvements and Bug fixes18/02/20262.5.29Various improvements and Bug fixes01/12/20252.5.13Hide height adjustable arrowsVarious improvements and Bug fixes13/10/20252.4.7Power control plug support for the Interact has been added. The Power Control Plug is an accessory for GoBright Interact that powers your desk workstation only when checked in, reducing energy use, saving costs, lowering your environmental impact, and increasing the accuracy of your occupancy data. For more information on thePower control plug, check out the GoBright helpcenter article. 03/07/20252.3.2Various improvements and Bug fixes18/06/20252.2.11Translation updates13/06/20252.2.9Various improvements and Bug fixes02/04/20252.1.1OMT support as new desk actuator. Demo mode available for showcasing Interact functions.25/02/20252.0.0A fully updated look and feel, improving the overall user experience.Driving the desk up and down can now be done with just a simple swipe up/down to drive to the desired position: Swipe up to move to standing preset, and swipe down to move to sitting preset.When a desk is closed in the system, the Interact will also show the desk as being closed.Even further back-dated firmware (not recommended by Ascentae):24/01/20251.9.7  Internal sensor (Beta): Improved the Machine Learning algorithm of the built in vibration sensor, to even more accurately detect occupancy.17/12/20251.9.5NFC emulation: Users will now be able to book/check in with the NFC via their smartphone. This will give users more options to book a desk.Internal sensor (Beta): The interact has a built in vibration sensor. This can now be activated for occupancy detection, automatic check in and auto release. This will provide more accurate data and a better user experience. 18/10/20251.8.5Added support for LogicData CB desks (beta).Added support for LogicData DM desks (beta)Added support for Jiecang desks (beta)Touch screen fixes & touch response improvementsGlow fix to turn off glow outside opening hours18/06/20241.6.2Support for 'Open WiFi' connectivityThe Interact can now be commissioned into 'Open WiFi' networks, where access is allowed based on the WiFi MAC addressThe Interact needs to be updated to this firmware version (or higher) to be able to be commissioned on an 'Open WiFi' networkSome for the archives....27/05/20241.6.1Improved support for LINAK desks, not requiring to update the controlbox anymore in specific scenario'sImproved decomissioning supportSeveral small improvements05/04/20251.4.9When linked to a room resource, check-in will not ask for credentials anymore (matching the behaviour of room panels)19/03/20251.4.8Improving Wifi reconnection logic when connection is lostAdded advanced system log storageSeveral minor system improvements05/03/20251.4.5Improving Wifi reconnection logic when connection is lostAdded advanced system log storageSeveral minor system improvementsThis release has a limited rollout, and is not yet available for all customers26/01/20251.2.0Support for Ethernet connectivity via the PoE Expansion Box.18/12/20231.1.17Various improvementsIf you have any questions, please log a ticket with our support desk.
2 hits
Lee Russell (@lee) March 2, 2026
Read More