Technical Resource Hub

If your IAdea panel has the GoBright app pre-loaded but you no longer need to use it, you can either disable it in the application menu or completely remove the app.Please note: USB drives must be formatted as FAT32. NTFS is not supported.Please select the best option for you below: Option 1 - Disabling the GoBright App 1) When the IAdea panel starts to load, you will see a circle with a pause icon in the middle. Press this button and enter 010101 as the code2) On the Basic Settings page, swipe down 2 / 3 times from the top of the screen to bring up the menu and press the settings cog in the bottom-right corner of the menu3) Now you're in the Android interface, select Apps & Notifications and See All Apps4) Select GoBright - Device5) Force stop the app and acknowledge the pop-up6) Select Disable and confirm the pop-up again. Follow any further prompts after thisNow this page will change to show an option to enable GoBright again.Press the back arrow in the top-left corner a few times to return to the Android settings page. Now press the triangle in the bottom menu to return to the IAdea black settings screen.Plug in your relevant USB drive with the new .apk file you wish to install pre-loaded onto it. Swipe down a few times from the top of the screen and select the name of the USB drive and run the installer. Option 2 - Force Removing the GoBright App You may wish to completely remove the GoBright app from the panel. First of all, please take note of all of the following information:Model number (e.g. WRP1000-H)S/N of the unitOperating system (e.g Android 12)Firmware versionMAC address - this bit is important - we are unable to help without thisNOTE: Do not send photos of your S/N(s) or MAC(s) - please type them in the body of your email to Ascentae Support. It's your responsibility to provide the complete MAC address(es) as we cannot process photos.All of the above can be found by rebooting the unit and pressing the the pause icon to stop the device booting into GoBright and launching the IAdea back-end. Please enter 010101 as the code.Work your way through the tabs on the menu on the left. For example, you can find the serial number and model number under the Information tab.The Next StepsEnable remote monitoring. Now that you've carried out the above steps and made a note of the information in points 1-5 above, complete the following. Once remote monitoring has been enabled, IAdea will connect your device to their IAdeaCare servers.In the IAdea backend (see above) head to System > Remote MonitoringToggle on this optionWait for the 'initializing' message to appear and then 'waiting for connection'. Hang tight, it's processing any updatesYou will then be presented with 'pairing...' along with a pairing code shortly after. This will be 6 digits.Make a note of this pairing code and leave the panel on this page and switched on.Provide all information to Ascentae and the tech team will liase with the techs at IAdea.The full cycle after IAdea push the update through can take around 10-15 minutes to complete and may reboot several times throughout the process.After this process is complete, you have a blank panel as if it had just left the factory.NOTE: Once the device has been reset by IAdea it cannot be rolled back - you will permanently lose all configuration settingsIf you're using Wi-Fi, you will need to reconfigure your network connection settings under the Network tab on the Android Interface after the process is complete. To get to this interface, swipe down twice from the top of the screen on the black IAdea page and press the settings cog (bottom-right).You can now install any app you wish to use on your IAdea panel and the GoBright app no longer exists.IAdeaCareIAdeaCare is comprehensive device management for all deployed IAdea devices, including essential tools for deployment, management, ongoing maintenance, and troubleshooting. IAdeaCare consolidates operational data from all your devices into a single intuitive interface for in-depth analysis or quick at-a-glance viewing.Please speak to your Ascentae Account Manager for pricing.

This article has moved. Please click here to view the guide.

The XDS-1588 and XDS-1588-A cannot exceed Android 7.1. The WRP-1000-A/H cannot  exceed Android 9. Please ensure camera capability before selecting your panel for visitor management if you will be taking a photo of the visitor or scanning QR codes.Last Updated:2nd of December 2025ModelGoBright App VersionAndroid OSCamera QR SupportAscentae approvedXDS-158812.24 to 14.157.1✔(2MP)✔✔XDS-1588-A12.24 to 14.157.1✔(2MP)✔✔WRP-1000-A/H13.28 to 14.159✔(8MP)✔✔WRP-1000-LN/A9❌❌❌WRP-1000-L V2N/AAndroid 12❌❌❌WRP-1000-A V2N/AAndroid 12✔ (8MP)✔✔WRP-1000-H V2N/AAndroid 12✔ (8MP)✔✔ RecommendationIf you are deploying new hardware, stick to the V2 (Android 12) to ensure security compliance (InfoSec). Android 9 is quite dated by modern enterprise standards.