Ascentae
Your current date and time:
Search All Vendors

Ascentae Technical Resource Hub

Have A Question?

Ctrl+Alt+Defeat The Chaos

gobright iadea biamp lenovo nuiteq ptzoptics Rocware Mersive maxhub logo rethink jupiter utelogy audiebant ProDVX Nureva gobright iadea biamp lenovo nuiteq ptzoptics Rocware Mersive maxhub logo rethink jupiter utelogy audiebant ProDVX Nureva
Sort:

Found 8 results

Installation 5 months ago

Factory Reset An Interact

Here's a simple guide to factory resetting your GoBright Interact.With a small screwdriver or a paperclip you can press the reset button for 5-10 seconds.Let the device fully reboot. You'll then need the GoBright app to scan the QR code shown on screen and link the Interact to the relevant desk / room.The GoBright app is available for free on both Apple and Android devices. Just check out your relevant app store and search for 'GoBright'.
22 hits
Lee Russell (@lee) February 10, 2026
Read More
Installation 1 month ago

ProDVX Firmware Re-Flash

If the device powers up as expected, but is stuck on the Android boot screen, please follow these steps to re-flash (factory reset) the ProDVX panel. You will need to re-install the relevant booking app after performing the following steps.Unplug everything from the device, including the power source.Press and hold the "Volume +" button.Whilst holding this button, provide power to the device (can be both PoE or PSU).Keep holding the button until the Android Recovery menu appears. In this menu, navigate using the volume (+/-) buttons to the format/wipe system option.Select this option by long pressing the circular menu button next to it.After confirming the reset, reboot the device and check and confirm whether it does so without any issues.After step 7, please be patient as it can take up to 10 minutes for the panel to reload. When the process is complete, you'll have a blank Android panel. As this process completely resets the panel, you'll need to reconfigure the network - so if you're using Wi-Fi you will need to re-authenticate.If you have any further questions, please contact support@ascentae.com to log a support ticket. It helps to speed things up if you provide:ModelSerial NumberProof of Purchase
9 hits
Lee Russell (@lee) June 22, 2026
Read More
Installation 5 months ago

Nureva HDL410 – Best Practice for Camera Integration Direct Integration

Nureva HDL410 – Best Practice for Camera IntegrationDirect Integration Before installing a camera steering and switching solution to integrate with your Nureva audio solution, we recommend you refer to the below information and important links.You can find comprehensive instructions on installing and configuring a Nureva / camera solution on the Nureva Support site.This article gives guidance you may not find online, plus some Top Tips that we have picked up.Understand the customer requirementsNureva can support both camera steering (tracking/switching presets), and camera switching (changing to different cameras).It is important to have a view of the customers room, and understand which areas of the room need to be covered by a camera.  From this, you can determine the number of cameras required and the fields of view.If you have any queries about this, please contact Ascentae for advice.  We can even offer a full pre-installation consultancy service to help with this.Understand the limitations of the technology – HDL300 / HDL310         When integrating with a HDL300 or HDL310, you have a single sound bar – and so only one point of reference.  The information passed to the camera controller is based on the central point of the sound bar.  This makes it an ideal solution for azimuth presets, with a single camera mounted in line with the centre of the sound bar.Typically, up to 8 presets can be configured, each covering 22.5° of the room.The same is true if you have the legacy Dual HDL300 system.  The reference point for camera tracking will be the centre point of the primary sound bar (plugged into port 1 on the Connect Module).  The 2nd sound bar is not used for camera tracking).If using more than one camera, the best position for the cameras is either side of the sound bar, each covering half the room and using 4 presets.Understand the limitations of the technology – HDL300 / HDL310The HDL410 has 2 sound bars and when correctly positioned in the room, they can deliver accurate X,Y coordinate information to the camera controller.  Depending on the sophistication of the camera controller, it can interpret those coordinates in different ways.                Select appropriate camera and steer to coordinate location                Select appropriate camera and steer using presets                Select appropriate camera and switch to pre-defined zoneNote:  Not all camera controllers support all these modes.  Refer the camera vendor documentation for details.Camera zoning is covered in detail in a separate knowledge base article.Choosing the correct cameraNureva have created a suite of API calls which different camera providers have utilized to integrate with the Nureva devices.  Currently these are Aver and Lumens, plus drivers and sound tracking modules by Crestron and Extron.Typically, each camera vendor has created a software camera controller (in some instances it may be a hardware device).  Nureva confirm compatibility with the camera controller.  However, not all cameras from a specific vendor will be supported on the controller software.  It is the responsibility of the integrator to confirm compatibility of cameras and camera control solution.Make sure you check the focus length / zoom capabilities of the proposed camera.  If you are installing in a large room, the camera should be able to zoom and focus clearly on the furthest participant.Currently supported camera drivers are as follows.Note that camera switching is not supported by PTZApp 2 (single camera only)Note that camera switching is not supported by CamConnect Lite (single camera only)Cameras that support preset recall and have a Crestron module can support sound location data.Cameras that support preset recall and have an Extron driver can support sound location data.Positioning of the Nureva Sound BarsFor the HL300 / HDL310 remember that the camera reference point is the centre of the sound bar.The ideal position for the sound bar is above the screen – allowing sufficient clearance for the audio to be reflected off the wall into the microphones.It is important that there is no obstruction underneath the sound bar as this will degrade audio quality and cause inaccurate sound location data.To ensure best audio performance, measure how far your screen sits from the wall, and mount the sound bar so the bottom is 1.5 x this distance.E.g.  if you screen sits 10cm proud of the wall, the bottom of the sound bar should be 15cm from the top of the screen.Refer to the Microphone clearance requirements guide for more detailshttps://support.nureva.com/docs/installation-hdl300-microphone-clearance-requirements-and-recommendations-2We recommend that cameras are mounted underneath the screen where possible, but if underneath HDL sound bar, allow at least 6” (15cm) clearance from the top of the camera to the bottom of the sound bar.Available ResourcesSupported camera solution - https://support.nureva.com/docs/supported-integrations-for-camera-switching-and-tracking-1Aver Integration Instructions - https://support.nureva.com/docs/integrate-aver-cameras-with-camera-trackingLumens Integration Instructions - https://support.nureva.com/docs/how-to-integrate-with-lumens-ptz-camerasCrestron Module Instructions - https://support.nureva.com/docs/use-crestron-sound-tracking-moduleExtron Driver Instructions - https://support.nureva.com/docs/using-extron-sound-tracking-driverWatch out for reflectionsCameras are dumb and can easily be confused by reflections in windows.Be mindful of setting presets that can catch reflected images, or setting the camera to track in areas where windows will reflect if it’s dark outside.Ideally, curtains or blinds will not only avoid this issue, but have the additional benefit of reducing echo and reverberation in the room and so improve performance of the HDL device.If in doubt, ask AscentaeWe are here to help.  Please ask if you need any guidance, or would like to engage us to do a consultation on HDL and camera integration.
8 hits
Nick Palmer (@nick) February 8, 2026
Read More
Installation 5 months ago

Reset an Interact

You must be an admin to perform this action as access to the settings is required. If you do not have access, please speak to your GoBright Administrator.The GoBright App must be installed on your phone and you must be logged in as an Administrator.To reset the GoBright Interact device, log in to the GoBright portal and head to Settings > Devices > Interacts.Delete the device (step 3 above).The device will then show as offline:Place your finger on the 'Offline' section and swipe down to bring up the following:Select recommission and then confirm you wish to recommissionThe Interact will rebootYou are then presented with a QR code that needs to be scanned.You now need the GoBright App. Load the App and click on the 3 horizontal lines in the top right to bring up the settings menuSelect Admin toolsSelect GoBright InteractsSelect 'Commission an Interact by QR code'Select your commissioning presetScan the QR code on your phone that is logged in with an admin accountComplete the next page and make sure the Interact is coupled to the correct room / desk / parking spaceSelect 'Commission Device'After approximately 30 seconds the device will reboot.If your device is stuck on 'Connecting MQTT over TLS' please ensure that the following firewall rules have been applied:Outbound 8883 - Traffic over MQTT over TLS to the GoBright platformThe full firewall configuration can be found here:https://support.gobright.com/hc/en-us/articles/360010024559-Firewall-configuration
4 hits
Lee Russell (@lee) February 8, 2026
Read More
Updates 5 months ago

GoBright Interact Udpates

Below you will find a table containing all the information regarding the GoBright Interact firmware updates.Date Firmware Notes26/03/20262.5.32Various improvements and Bug fixes18/02/20262.5.29Various improvements and Bug fixes01/12/20252.5.13Hide height adjustable arrowsVarious improvements and Bug fixes13/10/20252.4.7Power control plug support for the Interact has been added. The Power Control Plug is an accessory for GoBright Interact that powers your desk workstation only when checked in, reducing energy use, saving costs, lowering your environmental impact, and increasing the accuracy of your occupancy data. For more information on thePower control plug, check out the GoBright helpcenter article. 03/07/20252.3.2Various improvements and Bug fixes18/06/20252.2.11Translation updates13/06/20252.2.9Various improvements and Bug fixes02/04/20252.1.1OMT support as new desk actuator. Demo mode available for showcasing Interact functions.25/02/20252.0.0A fully updated look and feel, improving the overall user experience.Driving the desk up and down can now be done with just a simple swipe up/down to drive to the desired position: Swipe up to move to standing preset, and swipe down to move to sitting preset.When a desk is closed in the system, the Interact will also show the desk as being closed.Even further back-dated firmware (not recommended by Ascentae):24/01/20251.9.7  Internal sensor (Beta): Improved the Machine Learning algorithm of the built in vibration sensor, to even more accurately detect occupancy.17/12/20251.9.5NFC emulation: Users will now be able to book/check in with the NFC via their smartphone. This will give users more options to book a desk.Internal sensor (Beta): The interact has a built in vibration sensor. This can now be activated for occupancy detection, automatic check in and auto release. This will provide more accurate data and a better user experience. 18/10/20251.8.5Added support for LogicData CB desks (beta).Added support for LogicData DM desks (beta)Added support for Jiecang desks (beta)Touch screen fixes & touch response improvementsGlow fix to turn off glow outside opening hours18/06/20241.6.2Support for 'Open WiFi' connectivityThe Interact can now be commissioned into 'Open WiFi' networks, where access is allowed based on the WiFi MAC addressThe Interact needs to be updated to this firmware version (or higher) to be able to be commissioned on an 'Open WiFi' networkSome for the archives....27/05/20241.6.1Improved support for LINAK desks, not requiring to update the controlbox anymore in specific scenario'sImproved decomissioning supportSeveral small improvements05/04/20251.4.9When linked to a room resource, check-in will not ask for credentials anymore (matching the behaviour of room panels)19/03/20251.4.8Improving Wifi reconnection logic when connection is lostAdded advanced system log storageSeveral minor system improvements05/03/20251.4.5Improving Wifi reconnection logic when connection is lostAdded advanced system log storageSeveral minor system improvementsThis release has a limited rollout, and is not yet available for all customers26/01/20251.2.0Support for Ethernet connectivity via the PoE Expansion Box.18/12/20231.1.17Various improvementsIf you have any questions, please log a ticket with our support desk.
2 hits
Lee Russell (@lee) March 2, 2026
Read More
Installation 5 months ago

Removing The GoBright App - IAdea Panels

If your IAdea panel has the GoBright app pre-loaded but you no longer need to use it, you can either disable it in the application menu or completely remove the app.Please note: USB drives must be formatted as FAT32. NTFS is not supported.Please select the best option for you below: Option 1 - Disabling the GoBright App 1) When the IAdea panel starts to load, you will see a circle with a pause icon in the middle. Press this button and enter 010101 as the code2) On the Basic Settings page, swipe down 2 / 3 times from the top of the screen to bring up the menu and press the settings cog in the bottom-right corner of the menu3) Now you're in the Android interface, select Apps & Notifications and See All Apps4) Select GoBright - Device5) Force stop the app and acknowledge the pop-up6) Select Disable and confirm the pop-up again. Follow any further prompts after thisNow this page will change to show an option to enable GoBright again.Press the back arrow in the top-left corner a few times to return to the Android settings page. Now press the triangle in the bottom menu to return to the IAdea black settings screen.Plug in your relevant USB drive with the new .apk file you wish to install pre-loaded onto it. Swipe down a few times from the top of the screen and select the name of the USB drive and run the installer. Option 2 - Force Removing the GoBright App You may wish to completely remove the GoBright app from the panel. First of all, please take note of all of the following information:Model number (e.g. WRP1000-H)S/N of the unitOperating system (e.g Android 12)Firmware versionMAC address - this bit is important - we are unable to help without thisNOTE: Do not send photos of your S/N(s) or MAC(s) - please type them in the body of your email to Ascentae Support. It's your responsibility to provide the complete MAC address(es) as we cannot process photos.All of the above can be found by rebooting the unit and pressing the the pause icon to stop the device booting into GoBright and launching the IAdea back-end. Please enter 010101 as the code.Work your way through the tabs on the menu on the left. For example, you can find the serial number and model number under the Information tab.The Next StepsEnable remote monitoring. Now that you've carried out the above steps and made a note of the information in points 1-5 above, complete the following. Once remote monitoring has been enabled, IAdea will connect your device to their IAdeaCare servers.In the IAdea backend (see above) head to System > Remote MonitoringToggle on this optionWait for the 'initializing' message to appear and then 'waiting for connection'. Hang tight, it's processing any updatesYou will then be presented with 'pairing...' along with a pairing code shortly after. This will be 6 digits.Make a note of this pairing code and leave the panel on this page and switched on.Provide all information to Ascentae and the tech team will liase with the techs at IAdea.The full cycle after IAdea push the update through can take around 10-15 minutes to complete and may reboot several times throughout the process.After this process is complete, you have a blank panel as if it had just left the factory.NOTE: Once the device has been reset by IAdea it cannot be rolled back - you will permanently lose all configuration settingsIf you're using Wi-Fi, you will need to reconfigure your network connection settings under the Network tab on the Android Interface after the process is complete. To get to this interface, swipe down twice from the top of the screen on the black IAdea page and press the settings cog (bottom-right).You can now install any app you wish to use on your IAdea panel and the GoBright app no longer exists.IAdeaCareIAdeaCare is comprehensive device management for all deployed IAdea devices, including essential tools for deployment, management, ongoing maintenance, and troubleshooting. IAdeaCare consolidates operational data from all your devices into a single intuitive interface for in-depth analysis or quick at-a-glance viewing.Please speak to your Ascentae Account Manager for pricing.
2 hits
Lee Russell (@lee) February 19, 2026
Read More
Can't find it here? Click here to give our extended vendor search a shot for a deeper dive