When commissioning Interacts on site, these can only be commissioned via the GoBright App. Here's your initial quick checklist:✅ An Interact ✅ An admin account for the GoBright Portal ✅ A smartphone with the latest GoBright mobile app, logged in as an admin✅ An Interact profile (this is done the on portal)✅ If the devices sit behind a firewall, please ensure MQTT over TLS has been correctly configured.Please note: When using Wi-Fi:✅ 2.4 Ghz (supported)❌️ 5 Ghz (not supported)Now that all of the above are in place, please follow steps 1 to 3 on this article.Related Article:Hard-reset a GoBright Interact The full firewall rules can be found here.

Product Code: INT1-POE-DESKGoBright have released a PoE adapter for their Interact device. If you can't power the device over the 230V mains adapter, PoE is now here! As you can see, it comes with 3M adhesive to fix the device to a surface.This is the connection that needs to be plugged into the Interact device:You then have the expansion box:  Note: A network cable is not suppliedWe tested the device on the 12th of June 2024, using a "dumb" NETGEAR PoE switch and an Interact running Application Version 1.6.1. If you're using a managed switch, please ensure PoE is enabled on the port(s) that you connect the Interact(s) to. Some further photos that might help plan your installation:Important: When using Interacts, you must configure your firewall to allow outbound traffic over MQTT (port 8883) over TLS. NTP and DNS must also be correctly configured for the device to communicate with the GoBright platform. The firewall configuration can be found here.Please contact support@ascentae.com for any help.

Wi-Fi signal strength is measured in dBm, with values usually ranging from -30 dBm to -90 dBm. A value closer to 0 (e.g. -50 dBm) indicates a stronger, faster connection, while lower numbers (e.g. -80 dBm) indicates a weaker, slower, or unstable connection. -50 dBm to -60 dBm (Excellent/Good)-60 dBm to -70 dBm (Fair)-70 dBm to -80 dBm (Weak)-80 dBm to -90 dBm (Unusable)Walls and electronic interference will significantly drop the dBm value in your environment. Finding your dBm level on an InteractPress and hold the time in the top-right for a few secondsSelect open device infoHere you have 4 options on the left hand side. On this screen you can find:StatusIP addressMAC addressSSID Signal, channel and dBmAuth mode used (e.g WPA2 PSK)We need to concentrate on the 2nd option down - WiFi. There is a signal indicator that will fluctuate in real-time. Values between -50 dBm and -65 dBm are good.Important: Interacts operate on the 2.4 Ghz spectrum. 5 Ghz is not supported.Still having issues? Check out our on site install guide here.

The Control Plug is the solution for managing the power usage for your GoBright Interact. The solution is to power on your desk workstation only when checked-in.Summary, key points & benefits:Supports a Bluetooth range of up to 15mUp to 5 Interacts can be connected to a single Control PlugThe firmware version on the Interact must be running 2.4.7 or aboveOnly available for Interacts - GoBright Connects are not supportedAvailable in UK, EU and USA versionsEnergy Savings: Automatically cuts power to desk peripherals (monitors, docking stations, etc.) when the desk is not in use, reducing your impact on the environmentBy requiring a check-in to activate power, it ensures more reliable desk occupancy data for facility managersClick here to view the extensive installation guide from GoBright to get up and running.

Cable length: 1.5mThe cable will arrive in the packaging as illustrated.We have tested the cable with the following specifications:230V mains (UK) plug to USB-C adapterInput 100-240V50-60 HzOutput 5.0V / 3.0A / 15.0Wor9.0V / 2.77A / 25.0WBoth scenarios power up the Interact.As well as a 230V mains power adapter, we've also tested the following using a USB-C port: The USB-C port shown above has a maximum of 3A.The DC side is plugged into the Interact and the USB-C side is plugged into your adapter of choice.

If the device powers up as expected, but is stuck on the Android boot screen, please follow these steps to re-flash (factory reset) the ProDVX panel. You will need to re-install the relevant booking app after performing the following steps.Unplug everything from the device, including the power source.Press and hold the "Volume +" button.Whilst holding this button, provide power to the device (can be both PoE or PSU).Keep holding the button until the Android Recovery menu appears. In this menu, navigate using the volume (+/-) buttons to the format/wipe system option.Select this option by long pressing the circular menu button next to it.After confirming the reset, reboot the device and check and confirm whether it does so without any issues.After step 7, please be patient as it can take up to 10 minutes for the panel to reload. When the process is complete, you'll have a blank Android panel. As this process completely resets the panel, you'll need to reconfigure the network - so if you're using Wi-Fi you will need to re-authenticate.If you have any further questions, please contact support@ascentae.com to log a support ticket. It helps to speed things up if you provide:ModelSerial NumberProof of Purchase